H3c-technologies H3C WX5500E Series Access Controllers Instrukcja Użytkownika Strona 150
- Strona / 221
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
139
{ The latter configures a port to permit packets from only one isolate-user-VLAN to pass through.
Configuration procedure
To configure an isolate-user-VLAN, complete the following tasks:
1. Configure the isolate-user-VLAN.
2. Configure the secondary VLANs.
3. Associate the isolate-user-VLAN with the specified secondary VLANs.
4. Configure uplink and downlink ports in the following workflow:
a. Configure the uplink ports, for example, the port connecting Device B to Device A in Figure 41,
to operate in promiscuo
us mode in the specified VLAN, so that uplink ports can be
automatically added to the specified isolate-user-VLAN and the secondary VLANs associated
with the isolate-user-VLAN.
b. Configure the downlink ports, for example, the ports connecting Device B to hosts in Figure 41,
to operate in
host mode, so that downlink ports can be automatically added to the
isolate-user-VLAN associated with the secondary VLAN.
For more information about the promiscuous and host mode commands, see Layer 2—LAN
Switching Command Reference.
To configure an isolate-user-VLAN:
Ste
p
Command
Remarks
1. Enter system view.
system-view N/A
2. Create a VLAN and enter
VLAN view.
vlan vlan-id N/A
3. Configure the VLAN as an
isolate-user-VLAN.
isolate-user-vlan enable
By default, no isolate-user-VLAN is
configured.
4. Return to system view.
quit N/A
5. Create secondary VLANs.
vlan { vlan-id1 [ to vlan-id2 ] | all }
N/A
6. Configure Layer 2 isolation
between ports in the same
secondary VLAN.
isolated-vlan enable
Optional.
By default, ports in the same
secondary VLAN can
communicate with one another at
Layer 2.
This configuration takes effect only
after you configure all ports in the
same secondary VLAN to operate
in host mode and associate
secondary VLANs with an
isolate-user-VLAN.
7. Return to system view.
quit N/A
8. Associate the
isolate-user-VLAN with the
specified secondary VLANs.
isolate-user-vlan
isolate-user-vlan-id secondary
secondary-vlan-id [ to
secondary-vlan-id ]
By default, no isolate-user-VLAN is
associated with secondary VLANs.
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Powiązane produkty i podręczniki dla Routery H3c-technologies H3C WX5500E Series Access Controllers
(4 strony)
(18 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji