H3c-technologies H3C WX5500E Series Access Controllers Instrukcja Użytkownika Strona 127
- Strona / 221
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
116
Ste
p
Command
Remarks
1. Enter system view.
system-view N/A
2. Enter interface view or
port group view.
• Enter Layer 2 Ethernet
interface view:
interface interface-type
interface-number
• Enter Layer 2 aggregation
interface view:
interface
bridge-aggregation
interface-number
• Enter port group view:
port-group manual
port-group-name
Use one of the commands.
• The configuration made in Layer 2
Ethernet interface view applies only to the
port.
• The configuration made in port group
view applies to all ports in the port group.
• The configuration made in Layer 2
aggregate interface view applies to the
aggregate interface and its aggregation
member ports. If the system fails to apply
the configuration to the aggregate
interface, it stops applying the
configuration to aggregation member
ports. If the system fails to apply the
configuration to an aggregation member
port, it skips the port and moves to the
next member port.
3. Configure the link type of
the ports as access.
port link-type access
Optional.
By default, all ports are access ports.
4. Assign the access ports
to a VLAN.
port access vlan vlan-id
Optional.
By default, all access ports belong to VLAN
1.
Assigning a trunk port to a VLAN
A trunk port can carry multiple VLANs. You can assign it to a VLAN in interface view.
Configuration restrictions and guidelines
• To change the link type of a port from trunk to hybrid or from hybrid to trunk, you must set the link
type to access first.
• After configuring the PVID for a trunk port, you must use the port trunk permit vlan command to
configure the trunk port to allow packets from the PVID to pass through, so that the egress port can
forward packets from the PVID.
Configuration procedure
To assign a trunk port to one or multiple VLANs:
Ste
p
Command
Remarks
1. Enter system view.
system-view N/A
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Powiązane produkty i podręczniki dla Routery H3c-technologies H3C WX5500E Series Access Controllers
(4 strony)
(18 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.217 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji