H3c-technologies H3C WX6000 Series Access Controllers Instrukcja Użytkownika Strona 124
- Strona / 179
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
10-10
Follow these steps to enable the display of system information on a monitor terminal:
To do… Use the command… Remarks
Enable the monitoring of system
information on a monitor terminal
terminal monitor
Required
Enabled on the console and disabled on
the monitor terminal by default.
Enable the display of debugging
information on a monitor terminal
terminal debugging
Required
Disabled by default
Enable the display of log
information on a monitor terminal
terminal logging
Optional
Enabled by default
Enable the display of trap
information on a monitor terminal
terminal trapping
Optional
Enabled by default
Outputting System Information to a Log Host
To do… Use the command… Remarks
Enter system view
system-view
—
Enable information center
info-center enable
Optional
Enabled by default
Name the channel with a specified
channel number
info-center channel
channel-number
name
channel-name
Optional
See
Table 10-2 for default channel
names.
Specify a log host and configure
the parameters when system
information is output to the log host
info-center loghost
host-ip [
port
port-number ] [
channel
{ channel-number | channel-name }
|
facility
local-number ] *
Required
By default, the system does not
output information to a log host. If
you specify to output system
information to a log host, the
system uses channel 2 (loghost) by
default.
The value of the port-number
argument should be the same as
the value configured on the log
host, otherwise, the log host
cannot receive system information.
Configure the output rules of the
system information
info-center source
{
module-name |
default
}
channel
{
channel-number | channel-name }
[
debug
{
level
severity |
state
state } * |
log
{
level
severity |
state
state } * |
trap
{
level
severity |
state
state } * ] *
Optional
See
Default Output Rules of
System Information
.
Specify the source IP address for
the log information
info-center loghost source
interface-type interface-number
Optional
By default, the source interface is
determined by the matched route,
and the primary IP address of this
interface is the source IP address
of the log information.
Configure the format of the time
stamp for system information
output to the log host
info-center timestamp loghost
{
date
|
no-year-date
|
none
}
Optional
date
by default.
- Configuration Guide 1
- All Rights Reserved 2
- Trademarks 2
- Preface 3
- GUI conventions 4
- Symbols 4
- Network topology icons 4
- Obtaining Documentation 6
- Technical Support 6
- Documentation Feedback 6
- Table of Contents 8
- 2 Typical Network Scenarios 13
- Unified Switch Networking 14
- 3 Feature Matrixes 15
- 4 Command Matrixes 29
- Introduction 61
- Configuring Ping 61
- Tracert 64
- System Debugging 65
- 6 NTP Configuration 69
- NTP Message Format 71
- Operation Modes of NTP 72
- Symmetric peers mode 73
- Broadcast mode 73
- NTP Configuration Task List 74
- NTP Configuration Examples 83
- delay disper 89
- Root delay: 40.00 ms 89
- 7 SNMP Configuration 93
- SNMP Protocol Versions 94
- MIB Overview 94
- SNMP Configuration 95
- Configuring SNMP Logging 97
- Configuring SNMP Traps 98
- Configuring Trap Parameters 99
- Network requirements 101
- Configuration procedure 101
- 8 MIB Style Configuration 104
- 9 RMON Configuration 105
- RMON Groups 106
- Alarm group 107
- Private alarm group 107
- Configuration Procedure 109
- Configuration Prerequisites 109
- Information Center Overview 115
- System Information Format 120
- 11 NQA Configuration 136
- Basic NQA concepts 139
- NQA Configuration Task List 140
- Configuring the NQA Server 141
- Enabling the NQA Client 141
- Creating an NQA Test Group 142
- Configuring DHCP Tests 143
- Configuring DNS Tests 144
- Configuring FTP Tests 145
- Configuring HTTP Tests 146
- Configuring UDP Jitter Tests 147
- Configuration prerequisites 148
- Configuring UDP jitter tests 148
- Configuring SNMP Tests 149
- Configuring TCP Tests 150
- Configuring UDP Echo Tests 150
- Configuring UDP echo tests 151
- Configuring Voice Tests 152
- Scheduling an NQA Test Group 157
- NQA Configuration Examples 158
- 12 Index 178
Powiązane produkty i podręczniki dla Routery H3c-technologies H3C WX6000 Series Access Controllers
(85 strony)
(13 strony)Westin 363801W manuali
Manuali dei proprietari e guide per l'utente per Spremitori Westin 363801W.
We fornisce 1 manuali pdf Westin 363801W per scaricare gratuitamente in base al tipo di documento: Manuale di Manutenzione e Cura
Komentarze do niniejszej Instrukcji