H3c-technologies H3C WA2600 Series WLAN Access Points Instrukcja Użytkownika Strona 1

H3C WA2620i-AGN Access PointInstallation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: 6PW102-20130712

4 Console cable (provided with the fat AP only) Wall anchor kit Hex-head bolt, washer, and nut Rubber feet NOTE: Antennas, power adapter, and

5 Rubber hammer Phillips screwdriver Ladder

6 Installing the AP CAUTION: The WA2620i-AGN is usually installed on a high position, such as a wallor ceiling, so the maintenance personnel cannot

7 Check before installation Before you install an AP, check the following: • Connect the power cord and connect the AP to the network. Check the LED

8 Installing the AP NOTE: The WA2620i-AGN has integrated antennas. When you install the AP, determine whether external antennas (user-supplied) ar

9 Figure 5 Mounting the AP on the table Mounting the AP on a wall To mount the AP on a wall, you need a wall-mounting bracket and wall anchor kit.

10 To mount the AP on a wall: 1. Use the wall-mounting bracket as a template to mark the locations of the mounting holes on the bracket. Drill three

11 Figure 8 Inserting a wall anchor 3. Align the holes in the wall-mounting bracket with the anchors and insert screws through the installation ho

12 7. Mount the AP on the hook on the wall-mounting bracket. See callout 1 in Figure 10. 8. Pull down the AP with force until it clicks into place.

13 Figure 11 Bolt holes on the wall-mounting bracket (in mm) (1) through (3) Bolt holes To install the AP on a ceiling: 1. Drill two 5.0 mm (0.20

Copyright © 2011-2013, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmit

14 Figure 12 Mount the mounting bracket to a ceiling (1) Nut (2) Washer (3) Ceiling (4) Wall-mounting bracket (5) Hex-head bolt (6) Hook CAUTION

15 • The power supply is well grounded when the AP adopts local power supply. • The PoE power supply is well grounded when the AP adopts PoE power

16 PoE power supply CAUTION: • When you apply 802.3af PoE power supply, connect one end of the network cable to the network port on the AP, and th

17 Checking the network connection for the fit AP When the AP operates as a fit AP, all of its settings are configured on the AC. You can use the dis

18 Logging in to the fat AP NOTE: The WA2620i-AGN is usually installed on a high position. H3C recommends that you log in to the AP to configure r

19 Setting up the configuration environment NOTE: The serial ports on PCs do not support hot swapping. If the AP has been powered on, connect the

20 Figure 16 Connection description 3. Select the serial port to be used from the Connect using list, and click OK.

21 Figure 17 Set the serial port used by the HyperTerminal connection 4. Set Bits per second to 9600, Data bits to 8, Parity to None, Stop bits to

22 Figure 18 Set the serial port parameters NOTE: To restore the default settings, click Restore Defaults. The HyperTerminal window appears.

23 Figure 19 HyperTerminal window Logging in through the console port Power on the AP, and you can see the following information: System is startin

Preface The H3C WA2620i-AGN AP Installation Guide describes the hardware specifications, preparations before installation, installation procedure, cab

24 • Username—admin • Password—h3capadmin • Management IP address of VLAN-interface 1 of the AP—192.168.0.50, with the subnet mask 255.255.255.0.

25 Appendix LEDs and ports LEDs Table 3 describes the LEDs provided by the WA2620i-AGN. Table 3 LED description Mark Color Status Description Green

26 Mark Color Status Description Flashing at 1 Hz The AP cannot detect any radio interface. Flashing at 8 Hz An Ethernet port or radio interface is o

27 Figure 20 WA2620i-GN ports (1) 2.4G antenna port 2 (2) 2.4G antenna port 1 (3) 5G antenna port 1 (4) 5G antenna port 2 (5) Reset button (6) Co

28 Port Standards and protocols Description ETHERNET • IEEE802.3 • IEEE802.3u • IEEE802.3af 10/100/1000 Mbps copper Ethernet port .The Ethernet po

29 Index A C D I L P S U A Accessories provided with the AP,3 C Check before installation,7 Connecting the AP to the network,16 Connecting the powe

Symbols Convention Description WARNING An alert that calls attention to important information that if not understood or followed can result in person

Documentation feedback You can e-mail your comments about product documentation to [email protected]. We appreciate your comments.

i Contents Product overview ······························································································ 1Preparing for installatio

1 Product overview The H3C WA2620i-AGN Access Point has integrated antennas, and also supports external antennas. The WA2620i-AGN can serve as a fit

2 Figure 2 Deployment of the AP on hotspots (fat AP) Table 1 Basic configuration Dimensions (H × W × D) Weight Max. power Enclosure Protocol Power

3 Preparing for installation Safety recommendations WARNING! Only qualified personnel can install and remove a WA2620i-AGN and its accessories. You